金属表面涂装行业VOCs排放特征及排放系数

对比了浙江省2014和2018年金属表面涂装企业的有机废气排放及治理情况,分析了该行业涂料及稀释剂的使用、主要污染因子,测算了溶剂型、水性涂料的挥发性有机物（VOCs）产生系数和排放系数.结果表明：2018年VOCs治理水平明显高于2014年,水性涂料使用企业比例由18%上升至36%,纯溶剂型企业由82%下降至64%;金属表面涂装行业的主要排放污染物为二甲苯、丁醇、乙酸乙酯、乙酸丁酯、甲苯、丙二醇、乙苯、苯乙烯等8种有机物.溶剂型和水性涂料的VOCs产生系数分别为0.72和0.31kg/kg;溶剂型和水性涂料2014年VOCs排放系数为0.64和0.29kg/kg,2018年为0.48和0.21kg/kg.     

模拟土壤淋洗废液中重金属的选择性去除与淋洗液的回收研究

土壤淋洗废液中污染物的选择性去除是实现淋洗液回收的关键.本文以硫化钠（Na₂S）、乙基黄原酸钾（PEX）、二甲基二硫代氨基甲酸钠（DTC）作为重金属沉淀剂处理电子垃圾污染土壤模拟淋洗废液,在筛选出Na₂S作为理想重金属沉淀剂的基础上,研究初始pH值、反应温度、沉淀剂浓度等因素对Na₂S分离络合态重金属的影响,并通过软件模拟和产物表征等方式推测反应机理.结果表明：Na₂S对柠檬酸络合态重金属的分离顺序依次为Cu、Pb、Cd,符合硫化物溶度积原则;反应温度、初始pH值对Na₂S处理络合态重金属无显著影响,重金属去除率均保持在90%以上,柠檬酸的回收率约为95%;Visual MINTEQ模拟结果显示,S^2-投加前液相中重金属主要以H₂CA^-、HCA^2-和CA^3-结合形式存在,S^2-投加后液相中重金属则以HS^-和S^2-结合形式存在;扫描电镜及能谱（SEM-EDS）表明,S^2-与金属阳离子按物质的量比1：1生成硫化物沉淀物,沉淀主要呈团聚、成簇和圆片状存在;X射线衍射（XRD）分析结果表明,沉淀产物中存在CuS、CdS、PbS和CuPbS₂.本研究结果可为化学沉淀法处理重金属污染土壤淋洗废液提供技术参考.     

高原高寒污水处理系统的微生物群落特征

为研究高原高寒污水处理系统活性污泥的微生物群落结构及多样性,以拉萨、云南、四川的3座高原污水厂作为实验组,同时以重庆2座非高原污水厂作为对照,采用PCR-DGGE技术对比分析了高原与非高原污水厂的微生物特性.研究表明：高原污水厂样品与非高原样品在聚类中展现出了较为疏远的关系,微生物群落区别明显.受强紫外线辐照的抑制,高原高寒污水处理系统微生物多样性的平均水平显著低于非高原污水厂,较低的微生物多样性是导致高原高寒地区污染物去除效果不佳的一项重要原因.群落构成方面,共鉴定出16个优势菌属,对应Proteobacteria、Bacteroidetes、Firmicutes、Verrucomicrobia 4个门.组间差异分析结果发现,高原组中丰度显著偏高的菌属只有Prosthecobacter,该菌在污水厂内分布广泛,且能够适应高原低温的条件.对于大多数活性污泥微生物而言,高原强紫外线是不利的生存条件.因此,减少高原露天污水处理系统的紫外辐照,是提升污水处理效能的一个潜在措施.     

DOC+CDPF对国III重型柴油货车实际道路排放的影响

利用便携式车载排放测试系统（PEMS）对2辆加装氧化催化转化器（DOC）和催化型柴油颗粒捕集器（CDPF）与否的国III重型柴油货车进行实际道路排放测试.结果表明,2辆改造重型柴油车的CO、THC、固态颗粒物粒数（SPN）和黑碳（BC）实际道路排放因子分别为（1.31±0.37）g/（kW×h）、（0.20±0.03） g/（kW×h）、（7.13×10¹⁰±5.27×10¹⁰）个/（kW×h）和（0.69±0.06）mg/（kW×h）,相对于原始排放（拆除DOC+CDPF）分别降低52.48%、55.69%、99.91%和99.22%.从低速、中速到高速,CO和THC减排比例呈现上升趋势,然而运行工况对SPN和BC减排比例则无显著影响.加装DOC+CDPF会导致NO₂在NO_x中的占比升高,且从低速、中速到高速涨幅依次增大,但对NO_x无明显减排效益,其排放因子为9.53~9.83g/（kW×h）,远高于实验室排放限值.     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Performance of different macrophytes in the decontamination of and electricity generation from swine wastewater via an integrated constructed wetland-microbial fuel cell process

Plants constitute a major element of constructed wetlands(CWs).In this study,a coupled system comprising an integrated vertical flow CW(IVCW) and a microbial fuel cell(MFC) for swine wastewater tre atment was developed to research the effects of macrophytes commonly employed in CWs,Canna indica,Acorus calamus,and Ipomoea aquatica,on decontamination and electricity production in the system.Because of the different root types and amounts of oxygen released by the roots,the rates of chemical oxygen demand(COD) and ammonium nitrogen(NH_4~+-N) removal from the swine wastewater differed as well.In the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,the COD removal rates were 80.20%,88.07%,84.70%,and 82.20%,respectively,and the NH_4~+-N removal rates were 49.96%,75.02%,70.25%,and 68.47%,respectively.The decontamination capability of the Canna indica system was better than those of the other systems.The average output voltages were 520±42,715±20,660±27,and 752±26 mV for the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,respectively,and the maximum power densities were 0.2230,0.4136,0.3614,and0.4964 W/m~3,respectively.Ipomoea aquatica had the largest effect on bioelectricity generation promotion.In addition,electrochemically active bacteria,Geobacter and Desulfuromonas,were detected in the anodic biofilm by high-throughput sequencing analysis,and Comamonas(Proteobacteria),which is widely found in MFCs,was also detected in the anodic biofilm.These results confirmed the important role of plants in IVCW-MFCs.     

Preparation of solar-enhanced AlZnO@carbon nano-substrates for remediation of textile wastewaters

Photoactive aluminum doped ZnO(AlZnO) was synthesized by sol-gel method.After that,AlZnO photocatalyst was deposited on five carbon-based materials(CBMs) using ultrasonic route followed by solid-state mixing using ball mill.The CBMs used were poly aniline(PANI),carbon nitride(CN),carbon nanotubes(CNT),graphene(G),and carbon nanofibers(CNF).The crystal phases,elemental compositions,morphological,and optical properties of the AlZnO@CBMs composites were investigated.Experimental results revealed that two of AlZnO@CBMs composites exhibited superior bleaching efficiency(100% removal) and photocatalytic stability(three cycles) for 50 μmol/L Methylene Blue(MB) contaminated water after 60 min irradiation in visible light at pH 6.5,0.7% H_2O_2,and 5 g/L inorganic salts.Under optimum conditions,AlZnO@CBMs nanocomposites were employed for the treatment of mixed dyestuffs composed of MB,Methyl Orange(MO),Astrazone Blue FRR(BB 69),and Rhodamine B(RhB) dyes under dark,ultraviolet,visible,and direct sunlight.For mixed dyestuffs,the AlZnO@G achieved the highest dye sorption capacity(60.91 μmol dye stuffs/g) with kinetic rate 8.22 × 10~(-3) min~(-1) in 90 min via multi-layer physisorption(Freundlich isotherm) on graphene sheet.In additions,AlZnO@CN offered the highest photo-kinetic rate(K_(photo)) of～54.1 × 10~(-3) min~(-1)(93.8% after 60 min) under direct sunlight.Furthermore,the selective radical trapping experiment confirmed that the holes and oxidative superoxide radicals are crucial on dyes photodegradation pathway.Owing to their superior performance,AlZnO@G and AlZnO@CN nanocomposites can offer an effective in-situ solar-assisted adsorption/photocatalytic remediation of textile wastewater effluents.     

精神活性物质在北京市某污水处理厂中的污染特征与生态风险

为了解污水处理厂对精神活性物质的去除特征及总出水对受纳水体的生态风险,采用固相萃取-高效液相色谱-串联质谱法调查了北京市某污水处理厂中13种精神活性物质的浓度水平与负荷量变化,并运用RQ（risk quotient,风险熵）对总出水中精神活性物质进行风险评估.结果表明:①13种精神活性物质在总进水与总出水中均能检出,总质量浓度平均值分别为2 395.10和63.59 ng/L,其中ρ（EPH）（EPH表示麻黄碱）占比分别为93.9%和67.9%,其次为COD（可待因）与METH（甲基苯丙胺）.污水处理厂上游地表水中ρ（EPH）、ρ（METH）与ρ（KET）（KET为氯胺酮）均高于总出水及其下游地表水,说明上游沿河可能有新的污染源输入.②污水处理厂对NK（去甲氯胺酮）、BE（苯甲酰爱康宁）和MTD（美沙酮）均呈负去除,其他精神活性物质的去除主要发生在二级生物处理与三级处理（超滤膜与UV消毒）阶段.③污水处理厂服务区域内精神活性物质的周内负荷量存在一定波动,AMP（苯丙胺）、METH、MDA（3,4-亚甲二氧基苯丙胺）、MDMA（3,4-亚甲二氧基甲基苯丙胺）、KET与HER（海洛因）的负荷量均在周末升高.④污水处理厂总出水中精神活性物质的生态风险均较低（RQ < 0.10）.研究显示,污水处理厂不能完全去除污水中的精神活性物质,总出水中残留精神活性物质对受纳河流生态系统产生的长期混合效应不容忽视.      

废塑料再生过程废水中微塑料去除模拟试验

微塑料是一种存在于不同环境介质中的新兴污染物,主要来源于废弃塑料制品,其存在污染范围广、潜在环境污染大的问题.废塑料再生企业生产废水中微塑料浓度远高于其他类型废水,对其生产废水中的微塑料进行处理具有重要的环境意义.模拟废塑料再生过程的生产废水并进行微塑料去除的絮凝沉淀试验,研究絮凝剂投加量、pH、水力快速搅拌条件的单因素和正交试验对废水中微塑料去除率及其各因素作用的影响.结果表明:①当PAC (聚合氯化铝)投加量为10 mL,PAM (聚丙烯酰胺)投加量为7 mL,pH为9,水力快速搅拌条件为100 r/min下维持40 s再200 r/min下维持40 s时,微塑料的总去除率最高,达91%.②PAC投加量是影响微塑料去除效果的主要因素,其次是pH.③微塑料的去除率与其本身的密度有关,密度大的ABS (acrylonitrile butadiene styrene,丙烯腈-丁二烯-苯乙烯)去除率最高,密度小的PE (polyethylene,聚乙烯)去除率最低.④不同粒径区间的微塑料去除率区别较大,粒径小(0.1~0.25 mm)的微塑料去除效果最好.研究显示,通过控制PAC和PAM的投加量、pH和水力搅拌速率等条件,能够有效将废水中的微塑料通过絮凝沉淀的方法去除,从而达到净化含微塑料生产废水的目的.      

2-丁烯醛生产废水的臭氧脱毒预处理

CMW（crotonaldehyde manufacturing wastewater,2-丁烯醛生产废水）污染物浓度高、毒性强、直接采用生物法处理难度大.为了降低CMW的生物处理毒性,采用臭氧氧化法对CMW进行脱毒预处理,并通过考察不同臭氧氧化条件对废水COD_Cr、TOC（总有机碳）、UV_{254 nm}去除率及SMA（specific methanogenic activity,比产甲烷活性）抑制率的影响,获得了优化的臭氧氧化条件,进一步分析了废水脱毒机理.结果表明:①优化的臭氧氧化条件为接触反应时间180 min、初始pH 3.0、反应温度35℃、气相臭氧浓度30.3 mg/L,进气流量500 mL/min;并且在该条件下,CMW中COD_Cr、TOC和UV_{254 nm}的去除率分别为19.9%、9.9%和70.6%,主要特征有机污染物[包括2-丁烯醛、（E,E）-2,4-己二烯醛、3-（2-甲基-2-丙烯）-5-戊内酯、1,5-二甲基-1-烯-4-羰基-环氧己烷、山梨酸乙酯等]的去除率在74.4%以上.②厌氧产甲烷毒性试验结果显示,CMW的SMA抑制率由臭氧氧化前的82.0%降至臭氧氧化后的47.2%.③反应动力学研究显示,CMW中COD_Cr、TOC及UV_{254 nm}的去除过程均符合一级反应动力学方程,R2分别为0.82、0.97、0.94.研究显示,臭氧氧化预处理可以较好地去除CMW中的特征有机污染物,降低废水的厌氧生物处理毒性,是一种可行的脱毒预处理方法.